I have one hitch for your 2013 Mazda MX-5 Miata however, none of our spare tire carriers are small enough to fit it. The Curt Trailer Hitch item # C11028 is a class I hitch with a 1-1/4" receiver. Due to the small size and weight of your car this is the largest capacity hitch available.
All of our spare tire carriers like the Curt item # c31006 you were looking at fit a 2" class III receiver. Additionally, the owner's manuals prohibit the use of adapters like item # HTAD that would allow... view full answer...
The Spare Tire Carrier # FHG57ZR I feel is the best option to use with the 24x84 etrailer Cargo Carrier # e96ZR. This carrier has multiple bolt hole options and the bars on the other side allow you to distribute the weight across multiple bars on the rack. view full answer...
Hey Susan, the etrailer Trailer Hitch Receiver # e98853 will work fine as a mounting point for a spare tire carrier like # c31006. The receiver tube on this hitch is open all of the way through and theoretically you could access the back end of it but you wouldn't ever need to.
Finally, for a wiring harness I recommend going with the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56261 which just plugs into your OEM wiring, and gives you with a 4-pole connector. view full answer...
The simplest and most economical option is going to be the Hollywood Racks SR1 2-Bike Carrier # HRSR1. This does mount on the spare tire but the arms which hold the bike can be slide to the side allowing you to better center the bikes behind your 2004 Honda CR-V. Do understand the maximum weight for each bike is 35lbs for this and is common among these types of racks.
For a stronger rack that will be easier to use with your rear door you would want to add our Receiver # e69AR. This would... view full answer...
Hey Terry, thanks for reaching out!
The Roadmaster Spare Tire Mount # RM-195125 will reduce your tongue weight by 33% and adding an extension will not only increase the movement of the tire at the back of your motorhome, but it will also cut the tongue weight by an additional 50% so it wouldn't be safe to use the carrier in this manner.
For an alternative solution I recommend pairing the etrailer Spare Tire Mount # e98ZR with the Saris Swing Away Hitch Extender # SAR36VR so you can swing... view full answer...
The # LC159041 is designed to bolt onto a trailer frame so we really don't recommend it for a motorhome. I'm sure it is possible to make it work assuming you have the clearance and don't exceed the 150 lb capacity. However, you will likely need the help of a welder or fabricator to make it happen.
A better solution is to use the Roadmaster Hitch Spare Tire Mount with 2" Receiver Opening # RM-195225. This will let you mount it on the rear so it is out of the basement. It also has a 2"... view full answer...
While there are more budget friendly weight distribution hitches out there like the Reese # RE94FR you found, I highly recommend getting one with more quality like the Fastway e2 # FA92-00-0800. While both these have the same weight capacities of 400-800lbs of tongue weight and total trailer weight up to 8,000lbs the big difference is in the spring bars themselves. The Reese uses round bars which by bending the bars creates a weak point. And I cannot begin to tell you how many times I've... view full answer...
Hey Steve, I can definitely help with this. A lot to unpack here so I will do my best to cover everything. Let's start with the axle/spindles, since that will directly tie into what hubs, wheels and tires we end up going with.
As far as the axle, we do not have anything with a 54" hub face (HF) measurement. We do have the CE Smith Trailer Axle # CE33201GA-HUB, which has a 57-1/2" HF measurement. It is rated for 1,800 lbs and the axle itself is a 1-1/2" square tube. This axle also comes... view full answer...
For your 2024 Ice Castle I have a couple options you can choose from. If looks aren't a concern and you just want a spare to get you by in the event of a blowout I recommend the Diamondback ST235/80R16 Radial Trailer Tire w/ 16" Vesper White Spoke Wheel # TA64GR. This is a low cost spare that will get the job done.
If you're looking for something that closely matches your current wheel the Provider ST235/80R16 Radial Tire w 16" Viking Aluminum Wheel # A16RTK8BMMFLHD seems to be fairly... view full answer...
Bill yes, the Brass Tire Sensors for TST TPMS # TST-507-RV-S2 will work great with your TST TPMS for RVs - Color Display - Signal Booster # TST-507-RV-4-C.
These sensors were designed specifically to be used with that system as well as the 6 sensor version # TST-507-RV-6-C. view full answer...
Hi Tony,
For your specific needs I recommend the Lets Go Aero V-Lectric FAT PRO Bike Rack for 2 Electric Bikes # LGA77FR. This rack is rated for use on all vehicles, trailers, motorhome, etc. and has a 75lb per bike capacity. It has an adjustable base so that you can place the bikes further out if you need more space for a cargo carrier or spare tire and comes with an anti-rattle hitch pin to prevent any movement of the rack in the trailer hitch.
I've attached a short video below where... view full answer...
There are some good bike rack options for the 2023 Jeep wrangler. Because of the design of the rear hatch and the placement of the spare tire there really will not be any good trunk mounted options, but there will be a few other directions we can go.
One option is to go with a spare tire mounted bike rack like the Hollywood Racks SR1 # HRSR1. This rack will install over the door mounted spare tire and it will fit virtually any tire up to 15" wide. It can hold two bikes weighing up to 35... view full answer...
To be able to verify the Dexter Trailer Idler Hub Assembly # 8-259-5UC1-EZ is the correct part for your axle I will either need the axle tag information on your 2023 Triton LTWCI trailer or I will need to know what bearings and grease seal your current hubs use. This hub uses the bearing # L44649 for both the inner and outer position along with a Grease Seal # 10-9.
If this matches what you have the Hub # 8-259-5UC1-EZ will fit with the Aluminum Lynx Trailer Wheel # LH45FR and Taskmaster... view full answer...
The Silver Modular Trailer Wheel # LHHA315 from the Castle Rock ST205/75R15 Radial Trailer Tire w/ 15" Silver Mod Wheel # LHACK121 has a powder coat finish. While the Vesper wheel on the Provider ST205/75R15 Radial Trailer Tire w/ 15" Vesper Silver Mod Wheel # MX57FR has an acrylic enamel finish which is more durable than powder coat. Each manufacturer is going to have their own specific paint codes they use but the Wheel and Tire # LHACK121 you found does appear to have the darker finish.... view full answer...
David, there are trailer hitches for your 2021 Toyota Highlander. I recommend checking out the etrailer Trailer Hitch Receiver # e75ZR. This is a class III (2" x 2") hitch with a 5,000 lb weight capacity, and a 500 lb tongue weight capacity so you'll get plenty of capacity to do whatever you want (within reason).
As far as your spare goes, if it's smaller than 18" then this hitch will work with it, but if it's bigger then you'll have to permanently remove it. view full answer...
Hey Rob,
The Hellwig Big Wig Rear Anti-Sway Bar # HE92RR installs with the end links behind the axle with a mounting bracket right by the spare tire. The Roadmaster Rear Anti-Sway Bar # RM-1129-130 installs with the end links in front of the axle. I personally wouldn't want anything else in the way near the spare tire and with the # RM-1129-130 being slightly thicker I'd have to recommend Roadmaster for your Ram.
The SuperSprings SuperSway Stops # SS75GR are a fit for your Ram as well... view full answer...
Thanks for the pictures! Since a 215/60-8 Bias Trailer Tire like item # AM3H300 is 18.3" tall x 8.9" wide, I recommend a cover designed for 21" tall tires. The CE Smith Spare Tire Cover item # CE27410 was made for 21" x 6-1/2" tires so the extra height of the cover will compensate for the narrower width and be a nice fit on the tire.
Not sure what you meant by beer tire cover but all black is about the best option we have. We don't have too much variety in our tire covers but they work... view full answer...
Hey Teressa,
You can reply back to the email with those pictures and I'd be happy to take a look and see if we have a match. I did go ahead and copy a link below to our 15" wheel selection if you'd like to look through there as well. view full answer...
Hi Matthew,
For a paddle board as wide as your 34 inch L4, the best option to transport it on your roof is a carrier from Yakima:
- Yakima SUPDawg Stand-Up Paddleboard Carrier w/ Tie-Downs # Y04075
The SUPDawg # Y04075 can carry boards up to 36 inches wide, which is the most a carrier can handle, so you'll have a bit of room to spare; it also has a 66 lb capacity, which is just over what your board weighs. So it has the right specs to work with your SUP, but is also nice because it's... view full answer...
Kip, I actually don't know what wheels Black Rhino uses. We do have the Aluminum Liger Trailer Wheel # LH22FR which is 14", made by Lionshead and is gloss black so these could be the correct wheels but you'd have to give Black Rhino a call and see what they say. view full answer...
Go To Results